Basic Liquids - Revision history

Goober at 20:35, 5 November 2020

2020-11-05T20:35:54Z

← Older revision		Revision as of 20:35, 5 November 2020
Line 1:		Line 1:
			{{RF1Tutorial\|Volition}}

	To create a simple pool of water, follow these steps:		To create a simple pool of water, follow these steps:

Goober at 13:14, 30 October 2020

2020-10-30T13:14:26Z

← Older revision		Revision as of 13:14, 30 October 2020
Line 2:		Line 2:

	# create an average room-size air brush (about 4 meters high with a width and depth of 12 meters).		# create an average room-size air brush (about 4 meters high with a width and depth of 12 meters).

	# Make a second smaller air brush in the floor of the room to act as the pool. (note: if you have areas in your room that is lower than the pool of water, you may want to make the room it’s own portal so the water won’t fill from lower points in the room)		# Make a second smaller air brush in the floor of the room to act as the pool. (note: if you have areas in your room that is lower than the pool of water, you may want to make the room it’s own portal so the water won’t fill from lower points in the room)

	# Put a "Room Effect" object in the pool air brush and set it’s "Effect Type" property to "Liquid Room" in the pulldown. (note: hit CTRL+P on the selected object to bring up it’s properties dialog).		# Put a "Room Effect" object in the pool air brush and set it’s "Effect Type" property to "Liquid Room" in the pulldown. (note: hit CTRL+P on the selected object to bring up it’s properties dialog).

	# While in the properties dialog for the Room Effect object, go ahead and play with the liquid properties to get the type of water effect you want. Make sure you at least give it a water texture and set a good Depth for your pool of water.		# While in the properties dialog for the Room Effect object, go ahead and play with the liquid properties to get the type of water effect you want. Make sure you at least give it a water texture and set a good Depth for your pool of water.

	# Now add a light to the room so you can see the water in the game, rebuild and re-light your level, then run it.		# Now add a light to the room so you can see the water in the game, rebuild and re-light your level, then run it.

Goober: Created page with "To create a simple pool of water, follow these steps: # create an average room-size air brush (about 4 meters high with a width and depth of 12 meters). # Make a second sma..."

2020-10-30T13:14:14Z

Created page with "To create a simple pool of water, follow these steps: # create an average room-size air brush (about 4 meters high with a width and depth of 12 meters). # Make a second sma..."

New page

To create a simple pool of water, follow these steps:

# create an average room-size air brush (about 4 meters high with a width and depth of 12 meters).

# Make a second smaller air brush in the floor of the room to act as the pool. (note: if you have areas in your room that is lower than the pool of water, you may want to make the room it’s own portal so the water won’t fill from lower points in the room)

# Put a "Room Effect" object in the pool air brush and set it’s "Effect Type" property to "Liquid Room" in the pulldown. (note: hit CTRL+P on the selected object to bring up it’s properties dialog).

# While in the properties dialog for the Room Effect object, go ahead and play with the liquid properties to get the type of water effect you want. Make sure you at least give it a water texture and set a good Depth for your pool of water.

# Now add a light to the room so you can see the water in the game, rebuild and re-light your level, then run it.

[[Category: Red Faction]]
[[Category: RF1 Editing]]
[[Category: Tutorials]]
[[Category: Archived RF1 Content]]